CAD SchemCAD
IC Nguồn Xung 3V/5V (3.3V/5V Buck PWM)RichtekWQFN-20 (3x3mm)

RT6585AGQW — Datasheet PDF, Sơ đồ chân (VIN, LDO3, LDO5, ENLDO/ENM), Mã lưng SMD, IC Tương đương & Main xác

Low-Quiescent Dual 5V / 3.3V Step-Down Controller with LDO3 Always-On (top mark 5Y= / 3J=)

Hãng sản xuất
Richtek
Kiểu chân (Package)
WQFN-20 (3x3mm)
Điện áp vào (VIN / VCC)
5.5V – 25V
Ngõ ra / Cấu trúc
Dual 5V / 3.3V Buck PWM (Ultra-Low Iq)
Mã lưng SMD

Bảng Đo Đạc Đồng Hồ & Điều Kiện Chạy (Pinout) — RT6585AGQW

Chân # Tên Lệnh / Tín Hiệu Chức Năng Áp Chuẩn / Hướng Dẫn Đo Kiểm
11VINpower_inMain supply input 5.5V–25V from B+
15LDO3outputs3.3V LDO output for standby EC rail
14LDO5outputs5V LDO output for internal MOSFET gate drivers
12/13ENLDO/ENMcontrolLDO enable (pin 12) and master PWM enable (pin 13)
2/4ENTRIP1/ENTRIP2controlChannel 1/2 enable & OCP threshold resistor to GND
6PGOODoutputsPower-Good open-drain indicator

Mã Lưng SMD & IC Thay Thế Tương Đương

Mã Ký Hiệu Lưng SMD
IC Tương Đương Thay Thế Chân-Đổi-Chân

Luôn đối chiếu sơ đồ chân QFN/SOIC và mức tích cực của lệnh ACOK / EN trên schematic trước khi đóng IC tương đương.

Main Xác Laptop (Donor Motherboards) Có Chứa RT6585AGQW

Tìm kiếm vị trí RT6585AGQW trên 39.000+ schematic & BoardView tại SchemCAD.

🔎 RT6585AGQW →

Câu Hỏi Kỹ Thuật Thường Gặp — RT6585AGQW

What is RT6585AGQW used for on a laptop motherboard?
RT6585AGQW by Richtek is a IC Nguồn Xung 3V/5V (3.3V/5V Buck PWM) integrated circuit in a WQFN-20 (3x3mm) package (input voltage 5.5V – 25V; output/spec: Dual 5V / 3.3V Buck PWM (Ultra-Low Iq)). Low-Quiescent Dual 5V / 3.3V Step-Down Controller with LDO3 Always-On (top mark 5Y= / 3J=)
What is the SMD marking code for RT6585AGQW?
The top silkscreen SMD marking code for RT6585AGQW is 5Y=, 3J= (trailing characters on the package represent factory date/lot codes). Known pin-compatible equivalents: RT6585B.
What are the key diagnostic pins / startup conditions of RT6585AGQW?
Key multimeter diagnostic pin measurements for RT6585AGQW: Pin 11 (VIN): Main supply input 5.5V–25V from B+; Pin 15 (LDO3): 3.3V LDO output for standby EC rail; Pin 14 (LDO5): 5V LDO output for internal MOSFET gate drivers; Pin 12/13 (ENLDO/ENM): LDO enable (pin 12) and master PWM enable (pin 13); Pin 2/4 (ENTRIP1/ENTRIP2): Channel 1/2 enable & OCP threshold resistor to GND.
Which laptop motherboards use RT6585AGQW (donor boards)?
Use the SchemCAD interactive workbench or @BoardSchemBot to locate RT6585AGQW across 39,000+ laptop schematics and BoardView layouts.